Products

Each block is one machine type: photos, the numbers we actually publish, what it is for, and how a unit is selected. Final current and coil are set to your load.

8–15 kW 20–30 kW 30–80 kW Stainless Wall-hung boiler Coils & furnaces How we size and run

Wall-mounted controller — 8–15 kW

In stock · half-bridge · 380 V / 50 Hz

8-15 kW wall-mounted controller, open — Open — 345 × 160 × 180 mm

8-15 kW wall-mounted controller, closed — Closed enclosure

Power: 8–15 kW
Supply: 380 V / 50 Hz, 3-phase
Frequency: about 12 kHz
Size: 345 × 160 × 180 mm
Cooling: Forced air
Protection: Over-heat, over-current, coil short
Fits: Plastic barrels, small machines, energy retrofits on existing coils.

Use this if you need a compact wall box under 30 kW. Above 30 kW see the floor cabinets (full-bridge).

Mid-power — 20–30 kW

Half-bridge below 30 kW · controller shown 20–25 kW

20-30 kW mid-power cabinet — Mid-power cabinet

20-25 kW controller dimensions — 20–25 kW · 435 × 290 × 216 mm

Power: 20–30 kW class. White unit in the photo is 20–25 kW.
Topology: Half-bridge (all units below 30 kW)
Size (white controller): 435 × 290 × 216 mm
Fits: Machines and plant heat that sit between the wall-mount and the 30–80 kW cabinet.

If your load is under 30 kW, this is the mid size. Do not pick a 30–80 kW full-bridge cabinet unless the process needs that power.

Floor cabinet — 30–80 kW

In stock · full-bridge · painted steel

80 kW cabinet internals — Door open — 80 kW internals

Cabinet size 1000 x 450 x 300 mm — 1000 × 450 × 300 mm

Power: 30–80 kW
Supply: 380 V / 50 Hz, 3-phase
Frequency: about 12 kHz
Size: 1000 × 450 × 300 mm
Cooling: Forced air (water-cool optional on larger frames)
Protection: Over-heat, over-current, coil short
Fits: Plant rooms, reactor jackets, larger barrels, paper and pyrolysis cabinets.

Regular production item, available from stock. Full-bridge power stage (all units above 30 kW).

Stainless floor cabinet

Same power architecture · stainless enclosure

Stainless cabinet operator side — Operator side

Stainless cabinet cooling — Side / cooling

Enclosure: Stainless, built to the process.
Fits: Food-related or wet / wash-down plant rooms where painted steel is not wanted.

Ask for stainless when hygiene or corrosion is the issue. Power rating follows the load, not a separate kW list.

Wall-hung boiler — office and home

Space heating and domestic hot water

Wall-hung unit: Office or home space heating and hot water.
Industrial heater: Process water and bathing. Water and electricity are isolated.
Fits: Not a plastics-barrel controller. Use this line for water heating, not machine coils.

If you heat water or rooms, start here. If you heat a steel roll, barrel or furnace, use the induction cabinets and coils instead.

Coils and melting furnaces

Matched to the load · field install

Aluminum melting furnace — Aluminum melt ~700 °C

Zinc-alloy melting furnace — Zinc-alloy melt

Paper-machine coil hoist — Paper-machine coil

Bearing shrink-fit coil — Bearing shrink-fit

Pyrolysis heater cabinets — Pyrolysis cabinets

Aluminum furnace: Motor-rotor die-cast aluminum, working temperature about 700 °C.
Zinc furnace: Zinc-alloy electromagnetic melting.
Roll coils: Paper dryer/calender; textile transfer print, embossing, drying, setting; printing/packaging lamination; plastics/rubber calender; film and composite hot-press; coating drums.
Bearing coil: Shrink-fit and hot removal.
Tire pyrolysis: Induction on waste-tire oil-refining reactor jackets.

Coil and furnace jobs are sized from the process, not from a catalogue kW. Send photos and temperature. See Applications.

How a unit is selected and run

We do not publish a generic button-by-button manual here. Hardware and firmware are set to the coil. What is the same on every industrial cabinet:

Supply is 380 V / 50 Hz, 3-phase. Working frequency is about 12 kHz.
Below 30 kW the power stage is half-bridge; above 30 kW it is full-bridge. Do not mix those classes for the same load.
Cooling is forced air. Water-cool is optional on larger frames.
Protection covers over-heat, over-current and coil short. Units are aging-tested. Complete-machine warranty is two years.
Output current and inductance are matched to your coil at the factory. A coil from another maker needs its data, or we wind one.
To quote we need: process, material, target temperature, what you heat with now and its kW, and any CE or local-code requirement.

Send process data